This complete drain assembly kit is designed for This complete drain assembly kit is designed for use with both standard and whirlpool tubs. If it is, you'll see a 2-inch plastic pipe stubbing out of the wall under the sink. Turn on the faucet and observe the drain line. Then, put the faucet through the pre-drilled holes in the vanity top and tighten the nut included to keep it in place. Open the drain assembly packaging and examine the contents.
The main factor on deciding which one to use is cosmetic — will the drain line be visible? And leave the rags there for a couple of days, just in case a leak develops over time. Then, remove the old bathroom vanity shut-off valves and dispose of them. The bathroom sink drain connects to the drainpipe beneath the sink. Unscrew the nut from the inlet of the P-trap, and remove it and the plastic washer inside. If you have earlier used a threaded stopper, it is still possible to put the tape a couple of times around it. Then check the shutoff valves and pipe joints for leaks, and then turn on the faucet to check for leaks in the drain assembly.
In addition, going to the house with the main shut-off valve. If you have a multiple bowl sink, all of the drain tailpieces should be the same length for an easier installation. Make sure the top is level, and that all valves are clear of any drawers or other obstacles. Step 3: Fixing the Drain If you are replacing an existing drain pipe, then remove the nuts, bolts and connectors that join the drain pipe to the sink. They have standardized threads for ease of labor, which makes this an easy do-it-yourself project.
Step 1: Assembly Open the purchased drain pipe kit and confirm that all the parts mentioned on the box are in place and the function, utility and application of each part is understood. Bathroom sink drain installation is an easy process, provided that some simple steps are followed carefully. The twist and turn mechanism is built to last and the trim features a designer's touch of either Satin Nickel or Oil Rubbed Bronze. You should see a threaded strainer with a gasket and nut, and a tailpiece -- a short length of pipe that extends down from the drain under the sink. Set the P-trap opening against the washer and push up until the trap outlet is level with the waste pipe.
Slide the nut up along the tailpiece and fit the washer around the end of the tailpiece. . We have enough money a summit environment tall photo past trusted allow and all if youre discussing the domicile layout as its formally called. In most cases, you can reuse the current sink stopper and the accessories that make it work. The horizontal piece must fit inside the end of the drain line.
If your measurements are off or you don't tighten connections properly, the pipes will leak. You have it connected properly when you move the clevis rod up and down and the stopper moves correspondingly in the sink. Slide the nut down and screw it to the trap, tightening it as much as you can by hand. This threaded stopper will work as a bandage. Brass Bath Drain is designed for use with Whirlpool tubs. There should not be any kind of leaking or dripping of water. If you find any, tighten the compression nut again.
This nut will secure the washer beneath the sink and make a waterproof fitting. Step 11 — Test the New Sinks Turn the shut-off valves back on, and check for any leaks. They will also come in a kit that includes the clevis, nuts, washers and spring clips, to hook them up to any sink. Install new double-outlet valves by slotting in the supply pipe to the valve. Remove the screws or nails that hold the old vanity to the wall, and dispose of the old vanity.
Just shut off the water, take a deep breath, disassemble and reassemble the connection, and check again for leaks. Step 8 — Install the Vanity and Apply Silicone Now, you can install your new vanity. Line it up with an insertion hole on the sink stopper. Wrap the tape around the joint to ensure fixation. Constrict the trap with a washer provided and tighten it with the help of a pipe wrench. Measure the distance from the bottom of the vanity to the center of the pipe opening with a tape measure.
Compare the distance between the end of the tailpiece and the bottom of the vanity. Bathroom Sink Drain Hookup pictures in here are posted and uploaded by Adina Porter for your bathroom sink drain hookup images collection. If your sink has a pop-up stopper, be sure the hole in the tailpiece is facing the wall when you tighten the strainer. Fit a P-trap in place and tighten the slip nuts by hand. The oozed putty will ensure your drain is sealed. Step 4 — Turn the Main Supply On Turn the main water supply back on to check your plumbing for leaks.